View MC33207P_374289.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Order this document by MC33206/D
MC33206 MC33207
Advance Information
Rail-To-Rail Operational Amplifiers with Enable Feature
The MC33206/7 family of operational amplifiers provide rail-to-rail operation on both the input and output. The inputs can be driven as high as 200 mV beyond the supply rails without phase reversal on the outputs and the output can swing within 50 mV of each rail. This rail-to-rail operation enables the user to make full use of the supply voltage range available. It is designed to work at very low supply voltages (0.9 V) yet can operate with a single supply of up to 12 V and ground. Output current boosting techniques provide a high output current capability while keeping the drain current of the amplifier to a minimum. The MC33206/7 has an enable mode that can be controlled externally. The typical supply current in the standby mode is <1.0 A (VEnable = Gnd). The addition of an enable function makes this amplifier an ideal choice for power sensitive applications, battery powered equipment (instrumentation and monitoring), portable telecommunication, and sample-and-hold applications.
LOW VOLTAGE RAIL-TO-RAIL OPERATIONAL AMPLIFIERS
SEMICONDUCTOR TECHNICAL DATA
MC33206 P SUFFIX PLASTIC PACKAGE CASE 646
14 1
14 1
D SUFFIX PLASTIC PACKAGE CASE 751A (SO-14)
14 N.C. 13 VCC 12 Output 2
1
* * * * * * * * *
Standby Mode (ID 1.0 A, Typ) Low Voltage, Single Supply Operation (1.8 V and Ground to 12 V and Ground) Rail-to-Rail Input Common Mode Voltage Range Output Voltage Swings within 50 mV of both Rails No Phase Reversal on the Output for Over-Driven Input Signals High Output Current (ISC = 80 mA, Typ) Low Supply Current (ID = 0.9 mA, Typ) 600 Output Drive Capability Typical Gain Bandwidth Product = 2.2 MHz
16 1
N.C. 1 N.C. 2 Output 1 3 4 Inputs 1 5
2
11 10 9 8 Inputs 2 Enable 2 N.C.
Enable 1 6 VEE 7
(Dual, Top View) MC33207 P SUFFIX PLASTIC PACKAGE CASE 648
ORDERING INFORMATION
Operational Amplifier Function Dual MC33206P MC33207D Quad MC33207P Plastic DIP TA= -40 to +105C 40 105C Plastic DIP SO-16 Device MC33206D Operating Temperature Range Package SO-14
16 1
D SUFFIX PLASTIC PACKAGE CASE 751B (SO-16)
16 Enable 1, 4 15 Output 4
1 4
Output 1 1 2 Inputs 1 3
14 13 Inputs 4
VCC 4 5 Inputs 2 6
2 3
12 VEE 11 10 9 Inputs 3 Output 3
Output 2 7 Enable 2, 3 8
(Quad, Top View)
This document contains information on a new product. Specifications and information herein are subject to change without notice. (c) Motorola, Inc. 1996 Rev 0
MOTOROLA ANALOG IC DEVICE DATA
1
MC33206 MC33207
MAXIMUM RATINGS
Rating Supply Voltage (VCC to VEE) ESD Protection Voltage at any Pin Human Body Model Voltage at any Device Pin Input Differential Voltage Range Common Mode Input Voltage Range (Note 2) Output Short Circuit Duration (Note 3) Maximum Junction Temperature Storage Temperature Range Maximum Power Dissipation Symbol VS VESD VDP VIDR VCM ts TJ Tstg PD Value 13 2,000 VS 0.5 (Note 1) VCC + 0.5 to VEE - 0.5 (Note 3) +150 -65 to +150 (Note 3) Unit V V V V V sec C C mW
NOTES: 1. The differential input voltage of each amplifier is limited by two internal parallel back-to-back diodes. For additional differential input voltage range, use current limiting resistors in series with the input pins. 2. The common-mode input voltage range of each amplifier is limited by diodes connected from the inputs to both power supply rails. Therefore, the voltage on either input must not exceed either supply rail by more than 500 mV. 3. Power dissipation must be considered to ensure maximum junction temperature (TJ) is not exceeded. 4. ESD data available upon request.
DC ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = 0 V, VEnable = 5.0 V, TA = 25C, unless otherwise noted.)
Characteristic Input Offset Voltage (VCM 0 to 0.5 V, VCM 1.0 to 5.0 V) MC33206: TA = 25C MC33201: TA = -40 to +105C MC33207: TA = 25C MC33202: TA = -40 to +105C Input Offset Voltage Temperature Coefficient (RS = 50 ) TA = -40 to +105C Input Bias Current (VCM = 0 to 0.5 V, VCM = 1.0 to 5.0 V) TA = 25C TA = -40 to +105C Input Offset Current (VCM = 0 to 0.5 V, VCM = 1.0 to 5.0 V) TA = 25C TA = -40 to +105C Common Mode Input Voltage Range Large Signal Voltage Gain (VCC = 5.0 V, VEE = -5.0 V) RL = 10 k RL = 600 Output Voltage Swing (VID = 0.2 V) RL = 10 k RL = 10 k RL = 600 RL = 600 Common Mode Rejection (Vin = 0 to 5.0 V) Power Supply Rejection Ratio VCC/VEE = 5.0 V/Gnd to 3.0 V/Gnd Output Short Circuit Current (Source and Sink) Figure - Symbol VIO - - - - - VIO/T IIB - - - IIO - - - - VICR AVOL 50 25 - VOH VOL VOH VOL - - - CMR PSRR PSR ISC 4.85 - 4.75 - 60 - 66 50 4.95 0.05 4.85 0.15 90 25 92 80 - 0.15 - 0.25 - 500 - - dB V/V dB mA 300 250 - - V - VEE 5.0 10 VCC + 0.2 VEE - 0.2 50 100 VCC - V kV/V 80 100 200 250 nA - 0.5 1.0 0.5 1.0 2.0 8.0 11 10 13 - V/C nA Min Typ Max Unit mV
-
2
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
DC ELECTRICAL CHARACTERISTICS (continued) (VCC = 5.0 V, VEE = 0 V, VEnable = 5.0 V, TA = 25C, unless otherwise noted.)
Characteristic Power Supply Current (VO = 2.5 V, TA = -40 to +105C, per Amplifier) MC33206: VEnable = 5.0 Vdc MC33206: VEnable = Gnd (Standby) MC33207: VEnable = 5.0 Vdc MC33207: VEnable = Gnd (Standby) Enable Input Voltage (per Amplifier) Enabled - Amplifier "On" Disabled - Amplifier "Off" (Standby) Enable Input Current (Note 5) (per Amplifier) VEnable = 12 V VEnable = 5.0 V VEnable = 1.8 V VEnable = Gnd
NOTE:
Figure -
Symbol ID
Min
Typ
Max
Unit
- - - - - VEnable - - - IEnable - - - -
0.8 0.5 1.5 0.5 VEE + 1.8 VEE + 0.3 2.5 2.2 0.8 0
1.125 6.0 2.25 6.0 - -
mA A mA A V
A - - - -
5. External control circuitry must provide for an initial turn-off transient of <10 A.
AC ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = 0 V, VEnable = 5.0 V, TA = 25C, unless otherwise noted.)
Characteristic Slew Rate (VS = 2.5 V, VO = -2.0 to +2.0 V, RL = 2.0 k, AV = 1.0) Gain Bandwidth Product (f = 100 kHz) Phase Margin (RL = 600 , CL = 0 pF) Gain Margin (RL = 600 , CL = 0 pF) Channel Separation (f = 1.0 Hz to 20 kHz, AV = 100) Power Bandwidth (VO = 4.0 Vpp, RL = 600 , THD 1%) Total Harmonic Distortion (RL = 600 , VO = 1.0 Vpp, AV = 1.0) f = 1.0 kHz f = 10 kHz Open Loop Output Impedance (VO = 0 V, f = 2.0 MHz, AV = 10) Differential Input Resistance (VCM = 0 V) Differential Input Capacitance (VCM = 0 V) Equivalent Input Noise Voltage (RS = 100 ) f = 10 Hz f = 1.0 kHz Equivalent Input Noise Current f = 10 Hz f = 1.0 kHz Time Delay for Device to Turn On Time Delay for Device to Turn Off Figure - - - - - - - Symbol SR GBW Min 0.5 - - - - - - - - - - - ZO Rin Cin en - - - in - - - - ton toff - - 0.8 0.2 10 2.0 - - - - 25 20 - - - - - Typ 1.0 2.2 65 12 90 28 0.002 0.008 100 200 8.0 Max - - - - - - - - - - - k pF nV/ Hz pA/ Hz s s Unit V/s MHz Deg dB dB kHz %
OM
AM CS BWP THD
MOTOROLA ANALOG IC DEVICE DATA
3
MC33206 MC33207
Figure 1. Circuit Schematic (Each Amplifier)
VCC
VCC Vin - Enable Vin + VCC VCC
VEE
This device contains 96 active transistors (each amplifier).
PD(max) , MAXIMUM POWER DISSIPATION (mW)
Figure 2. Maximum Power Dissipation versus Temperature
4000 3500 3000 2500 2000 1500 1000 500 0 -60 SO-14/SO-1 6 -30 0 30 60 90 TA, AMBIENT TEMPERATURE (C) 120 150 14 Pin DIP PERCENTAGE OF AMPLIFIERS (%) 16 Pin DIP 40 35 30 25 20 15 10 5.0
Figure 3. Input Offset Voltage Distribution
360 amplifiers tested from 3 wafer lots VCC = 5.0 V VEE = Gnd TA = 25C DIP Package
0 -10 -8.0 -6.0 -4.0 -2.0 0 2.0 4.0 6.0 VIO, INPUT OFFSET VOLTAGE (mV)
8.0
10
4
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
Figure 4. Input Offset Voltage Temperature Coefficient Distribution
50 PERCENTAGE OF AMPLIFIERS (%) 40 30 20 10 0 -50 360 amplifiers tested from 3 wafer lots VCC = 5.0 V VEE = Gnd TA = 25C DIP Package 200 I IB , INPUT BIAS CURRENT (nA) 160 120 80 VCM > 1.0 V 40 0 -55 -40 -25 VCC = 5.0 V VEE = Gnd
Figure 5. Input Bias Current versus Temperature
VCM = 0 V to 0.5 V
-40
-30
-20
-10
0
10
20
30
40
50
0
25
70
85
125
TCVIO, INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT (V/C)
TA, AMBIENT TEMPERATURE (C)
Figure 6. Input Bias Current versus Common Mode Voltage
100 50 0 -50 A VOL , OPEN LOOP VOLTAGE GAIN (kV/V) 150 I IB , INPUT BIAS CURRENT (nA) 300 260 220 180 140
Figure 7. Open Loop Voltage Gain versus Temperature
-100 -150 -200 -250 0 VCC = 12 V VEE = Gnd TA = 25C 2.0 4.0 6.0 8.0 10 VCM, INPUT COMMON MODE VOLTAGE (V) 12
VCC = 5.0 V VEE = Gnd RL = 600 VO = 0.5 V to 4.5 V 0 25 70 85 TA, AMBIENT TEMPERATURE (C) 105 125
100 -55 -40 -25
Figure 8. Output Voltage Swing versus Supply Voltage
RL = 600 TA = 25C VSAT, OUTPUT SATURATION VOLTAGE (V) 12 10 VO,OUTPUT VOLTAGE (Vpp) 8.0 6.0 4.0 2.0 0 1.0
Figure 9. Output Saturation Voltage versus Load Current
VCC TA = -55C TA = 125C TA = 25C VCC - VCC - VEE + TA = 25C TA = -55C 0 5.0 10 IL, LOAD CURRENT (mA) 15 VEE + VEE 20
VCC = 5.0 V VEE = -5.0 V TA = 125C
2.0
3.0 4.0 5.0 VCC,VEE SUPPLY VOLTAGE (V)
6.0
MOTOROLA ANALOG IC DEVICE DATA
5
MC33206 MC33207
Figure 10. Output Voltage versus Frequency
CMR, COMMON MODE REJECTION (dB) 12 VO, OUTPUT VOLTAGE (Vpp) 100 80 60 40 20 0 10 k 100 k f, FREQUENCY (Hz) 1.0 M VCC = 6.0 V VEE = -6.0 V TA = -55 to +125C 10
Figure 11. Common Mode Rejection versus Frequency
9.0
6.0 VCC = 6.0 V VEE = -6.0 V RL = 600 AV = 1.0 TA = 25C
3.0
0 1.0 k
100
1.0 k 10 k f, FREQUENCY (Hz)
100 k
1.0 M
PSR, POWER SUPPLY REJECTION (dB)
120 100 PSR+ 80 60 PSR- 40 20 0 10 100 1.0 k 10 k f, FREQUENCY (Hz) 100 k 1.0 M VCC = 6.0 V VEE = -6.0 V TA = -55 to +125C
ISC , OUTPUT SHORT CIRCUIT CURRENT (mA)
Figure 12. Power Supply Rejection versus Frequency
Figure 13. Output Short Circuit Current versus Output Voltage
100 Source 80 60 Sink 40 20 0 0 1.0 2.0 3.0 4.0 5.0 6.0 Vout, OUTPUT VOLTAGE (V) VCC = 6.0 V VEE = -6.0 V TA = 25C
ISC , OUTPUT SHORT CIRCUIT CURRENT (mA)
Figure 14. Output Short Circuit Current versus Temperature
I CC, SUPPLY CURRENT PER AMPLIFIER (mA) 2.0 1.6 VCC = 5.0 V VEE = Gnd
Figure 15. Supply Current per Amplifier versus Supply Voltage with No Load
150 125
100 75 50 25 0 -55 -40 -25
Source Sink
TA = 125C 1.2 TA = 25C 0.8 TA = -55C 0.4 0 0
0 25 70 85 TA, AMBIENT TEMPERATURE (C)
105
125
1.0
2.0 3.0 4.0 5.0 VCC, VEE, SUPPLY VOLTAGE (V)
.0
6
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
Figure 16. Slew Rate versus Temperature
VCC = 2.5 V VEE = -2.5 V VO = 2.0 V GBW, GAIN BANDWIDTH PRODUCT (MHz) 2.0 4.0
Figure 17. Gain Bandwidth Product versus Temperature
VCC = 2.5 V VEE = -2.5 V f = 100 kHz
SR, SLEW RATE (V/ s)
1.5
3.0
+Slew Rate 1.0 -Slew Rate 0.5
2.0
1.0
0 -55 -40 -25
0
25
70
85
105
125
0 -55 -40 -25
0
25
70
85
105
125
TA, AMBIENT TEMPERATURE (C)
TA, AMBIENT TEMPERATURE (C)
Figure 18. Voltage Gain and Phase versus Frequency
A VOL, OPEN LOOP VOLTAGE GAIN (dB) VS = 6.0 V TA = 25C RL = 600 A VOL, OPEN LOOP VOLTAGE GAIN (dB) 70 50 40 70 50 30
Figure 19. Voltage Gain and Phase versus Frequency
CL = 0 pF TA = 25C RL = 600 40 80 120 160
80 120 1A
30 2A 10 1A - Phase, CL = 0 pF 1B - Gain, CL = 0 pF 2A - Phase, CL = 300 pF 2B - Gain, CL = 300 pF 100 k f, FREQUENCY (Hz) 1.0 M 2B 1B
O , EXCESS PHASE (DEGREES)
1A 2A
160 200 240 10 M
10 -10 -30 10 k 1A - Phase, VS = 6.0 V 1B - Gain, VS = 6.0 V 2A - Phase, VS = 1.0 V 2B - Gain, VS = 1.0 V 100 k f, FREQUENCY (Hz) 2B
1B
-10
200 240 10 M
-30 10 k
1.0 M
Figure 20. Gain and Phase Margin versus Temperature
70 Phase Margin 70 75
Figure 21. Gain and Phase Margin versus Differential Source Resistance
Phase Margin 75 60 VCC = 6.0 V VEE = -6.0 V TA = 25C 45 30 15 0 100 k
O M , PHASE MARGIN (DEGREES)
O M , PHASE MARGIN (DEGREES)
60 50 40 30 20 10 0 -55 -40 -25 Gain Margin 0 25 70 85 105 125 TA, AMBIENT TEMPERATURE (C) VCC = 6.0 V VEE = -6.0 V RL = 600 CL = 100 pF
60 A , GAIN MARGIN (dB) M 50 40 30 20 10 0
60 45 30 15 0 10 100 1.0 k 10 k RT, DIFFERENTIAL SOURCE RESISTANCE ()
Gain Margin
MOTOROLA ANALOG IC DEVICE DATA
7
MC33206 MC33207
Figure 22. Gain and Phase Margin versus Capacitive Load
80 16 VO , OUTPUT VOLTAGE (Vpp) Phase Margin Gain Margin VCC = 6.0 V VEE = -6.0 V RL = 600 AV = 100 TA = 25C 14 A , GAIN MARGIN (dB) M 12 10 8.0 6.0 4.0 2.0 0 100 CL, CAPACITIVE LOAD (pF) 1.0 k 0 10 5.0 VCC = 5.0 Vdc 4.0 3.0 2.0 1.0 VEE = Gnd CL = 0 pF AV = 1.0 TA = 25C 100 VCC = 2.0 Vdc 70 60 50 40 30 20 10 0 10
Figure 23. Output Voltage versus Load Resistance
O M , PHASE MARGIN (DEGREES)
1.0 k 10 k RL, LOAD RESISTANCE
100 k
Figure 24. Channel Separation versus Frequency
THD, TOTAL HARMONIC DISTORTION (%) 150 CS, CHANNEL SEPARATION (dB) 120 90 60 30 0 100 VCC = 6.0 V VEE = -6.0 V VO = 8.0 Vpp TA = 25C 1.0 k f, FREQUENCY (Hz) 10 k AV = 10 AV = 100 10
Figure 25. Total Harmonic Distortion versus Frequency
VCC = 5.0 V TA = 25C VO = 2.0 Vpp AV = 1000 0.1 AV = 100 AV = 10 VEE = -5.0 V RL = 600
1.0
0.01
AV = 1.0 100 1.0 k f, FREQUENCY (Hz) 10 k 100 k
0.001 10
en , EQUIVALENT INPUT NOISE VOLTAGE (nV/ Hz)
50 40 30 20 10 Noise Current 0 10 100 1.0 k f, FREQUENCY (Hz) 10 k Noise Voltage VCC = 6.0 V VEE = -6.0 V TA = 25C
5.0 4.0 3.0 2.0 1.0 0 100 k
8
MOTOROLA ANALOG IC DEVICE DATA
i n , INPUT REFERRED NOISE CURRENT (pA/ Hz)
Figure 26. Equivalent Input Noise Voltage and Current versus Frequency
MC33206 MC33207
GENERAL INFORMATION
The MC33206/7 family of operational amplifiers are unique in their ability to swing rail-to-rail on both the input and the output with a completely bipolar design. This offers low noise, high output current capability and a wide common mode input voltage range even with low supply voltages. Operation is guaranteed over an extended temperature range and at supply voltages of 2.0 V, 3.3 V and 5.0 V and ground. Since the common mode input voltage range extends from VCC to VEE, it can be operated with either single or split voltage supplies. The MC33206/7 are guaranteed not to latch or phase reverse over the entire common mode range, however, the inputs should not be allowed to exceed maximum ratings.
VO (1.0 V/DIV), V in (2.0 V/DIV)
Figure 28. ton Response
ton, TIME (2.0 s/DIV)
CIRCUIT INFORMATION
Rail-to-rail performance is achieved at the input of the amplifiers by using parallel NPN-PNP differential input stages. When the inputs are within 800 mV of the negative rail, the PNP stage is on. When the inputs are more than 800 mV greater than VEE, the NPN stage is on. This switching of input pairs will cause a reversal of input bias currents (see Figure 6). Also, slight differences in offset voltage may be noted between the NPN and PNP pairs. Cross-coupling techniques have been used to keep this change to a minimum. In addition to its rail-to-rail performance, the output stage is current boosted to provide 80 mA of output current, enabling the op amp to drive 600 loads. Because of this high output current capability, care should be taken not to exceed the 150C maximum junction temperature. Enable Function The MC33206/07 enable pins allow the user to externally control the device. (Refer to the Pin Diagram on the first page of this data sheet for enable pin connections.) If the enable pins are pulled low (Gnd) each amplifier (MC33206) and amplifier pair (MC33207) will be disabled. When the enable pins are at a logic high (VEnable VEE = 1.8 V) the amplifiers will turn "on". Refer to the data sheet characteristics for the required levels needed to change logical state. The time to change states (from device "on" to "off" and "off" to "on") is defined as the time delay. The Circuit in Figure 27 is used to measure ton and toff. Typical ton and toff measurements are shown in Figures 28 and 29. When the device is turned off (VEnable = Gnd) an internal regulator is shut off disabling the amplifier. Figure 27. Test Circuit for ton and toff
VCC
Figure 29. toff Response
VO (1.0 V/DIV), V in (2.0 V/DIV)
toff, TIME (2.0 s/DIV)
Low Voltage Operation The MC33206/07 will operate at supply voltages down to 1.8 V and ground. Since this device is a rail-to-rail on both the input and output, one can be assured of continued operation in battery applications when battery voltages drop to low voltage levels. This is called End of Discharge (see Figure 30). Now, the user can select a minimum quantity of batteries best suited for the particular design depending on the type of battery chosen. This will minimize part count in many designs. Figure 30. Typical Battery Characteristics
Type Alkaline NiCd NiMh Silver Oxide Lithium Ion Operating Voltage 1.5 V 1.2 V 1.2 V 1.6 V 3.6 V End of Discharge 0.9 V 1.0 V 1.0 V 1.3 V 2.5 V
MC33206 2.0 V VEnable ton toff 2.0 k
Vout ton toff
Compensating for Output Capacitance The combination of device output impedance and increasing capacitive loading will cause phase delay (reducing the phase margin) in any amplifier (Figure 22). If the loading is excessive, the resulting response can be circuit oscillation. In other words, an amplifier can become unstable when the phase becomes greater than 180 degrees before the open loop gain drops to unity gain. Figures 18 and 19 show this situation as frequency increases for a given load. The MC33206/7 can typically drive up to 300 pF loads at unity gain without oscillating.
MOTOROLA ANALOG IC DEVICE DATA
9
MC33206 MC33207
Figure 31. Capacitive Loads Compensation
Rf CX
RO CL Vin
RL
There are several ways to compensate for this phenomena. Adding series resistance to the output is one way, but not an ideal solution. A dc voltage error will occur at the output. A better design solution to compensate for higher capacitive loads would be to use the circuit in Figure 31. This design helps to counteract the loss of phase margin by taking the high frequency output signal and feeding it back into the amplifier inverting input. This technique helps to overcome oscillation due to a highly capacitive load. Keep in mind that compensation will have the affect of lowering the Gain Bandwidth Product (GPW). The values of CX and R0, are determined experimentally. Typical CX and CL will be the same value. Figure 32. Noninverting Amplifier Slew Rate
V , OUTPUT VOLTAGE (2.0 mV/DIV) O
SPICE Model If a SPICE Macromodel is desired for the MC33206/07, the user can define the characteristics from the following information. Obtain the SPICE Macromodel for the MC33204 Rail-to-Rail Operational Amplifier (device is the same as the MC33207). For the Enable feature of the MC33207, simulate it as a bipolar switch. The Macromodel does not include an input capacitance between the inverting and noninverting inputs. This capacitor is called Cin. Add 3.0 to 5.0 pF if stability analysis is required.
Figure 33. Small Signal Transient Response
V , OUTPUT VOLTAGE (50 mV/DIV) O VCC = 6.0 V VEE = -6.0 V RL = 600 CL = 100 pF TA = 25C
VCC = 6.0 V VEE = -6.0 V RL = 600 CL = 100 pF TA = 25C
t, TIME (5.0 s/DIV)
t, TIME (10 s/DIV)
Figure 34. Large Signal Transient Response
V , OUTPUT VOLTAGE (2.0 V/DIV) O VCC = 6.0 V VEE = -6.0 V RL = 600 CL = 100 pF AV = 1.0 TA = 25C
t, TIME (10 s/DIV)
10
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
OUTLINE DIMENSIONS
P SUFFIX PLASTIC PACKAGE CASE 646-06 ISSUE L
14 8
B
1 7
NOTES: 1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 4. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M N INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.300 BSC 0_ 10_ 0.015 0.039 MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.62 BSC 0_ 10_ 0.39 1.01
A F C N H G D
SEATING PLANE
L
J K M D SUFFIX PLASTIC PACKAGE CASE 751A-03 (SO-14) ISSUE F
-A-
14 8
-B-
1 7
P 7 PL 0.25 (0.010)
M
B
M
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION.
G C
R X 45 _
F
-T-
SEATING PLANE
D 14 PL 0.25 (0.010)
M
K TB
S
M A
S
J
DIM A B C D F G J K M P R
MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50
INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019
-A-
16 9
P SUFFIX PLASTIC PACKAGE CASE 648-08 ISSUE R
B
1 8
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01
F S
C
L
-T- H G D
16 PL
SEATING PLANE
K
J TA
M
M
0.25 (0.010)
M
MOTOROLA ANALOG IC DEVICE DATA
11
MC33206 MC33207
OUTLINE DIMENSIONS
D SUFFIX PLASTIC PACKAGE CASE 751B-05 (SO-16) ISSUE J
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019
-A-
16
9
-B-
1 8
P
8 PL
0.25 (0.010)
M
B
S
G F
K C -T-
SEATING PLANE
R
X 45 _
M D
16 PL M
J
0.25 (0.010)
TB
S
A
S
DIM A B C D F G J K M P R
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
12
MOTOROLA ANALOG IC DEVICE DATA MC33206/D
*MC33206/D*

▲Up To Search▲

Price & Availability of MC33207P

	To Download MC33207P Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .